Sellier & Bellot Exergy – 9,3×62 Factory Cartridge – Bullet test

We did a little Sellier & Bellot easter shootout earlier! Thank you for the Aseliike Remes to make it possible! This is the third and last part of the article series that will concentrate on the S&B Exergy factory cartridges.  We already published the 6,5×55 and 308win tests and this will concentrate on the 9,3×62 caliber. The S&B Exergy Blue bullet test articles will follow right after these Exergy articles!

Exergy is the original copper made hunting bullet of the Sellier & Bellot. At their homepage , they are writing that the jacket material of the Exergy, is not available. But on the Exergy 30-06 cartridge page, they are mentioning that it is made of 100% Solid Copper. So we cannot be sure about the exact material, but we know that it is a lead free bullet with little round aluminium tip on the top of the bullet.

Sellier Bellot exergy

But, to the results!

Sellier & Bellot Exergy 250gr –9,3×62 Factory Cartridge

TESTING

Test gun was a Blaser R8 rifle with the 480mm barrel. We measured the velocity ca. 5m from the muzzle and got a 714m/s (2343fps) impact velocity. Manufacturer promises the velocity of 745m/s (2444fps) to the factory load, from the 600mm barrel.

The slower impact velocity was achieved by reloading. If the velocity at the muzzle is 745m/s (2444fps) what manufacturer claims, the speed of 637m/s (2090fps) simulates the impact at the distance of 134 meters (ca. 146 yards).

THE BULLET

The working style of the S&B Exergy bullet is to open in five petals and retain its high weight after the impact without losing the petals.

The harder hit, with the velocity of 714m/s (2343fps) wasn’t too harsh for the 250gr Exergy, like it was for the 6,5×55 and 308win versions. Bullet opened all-the-way to the bottom of the expansion cavity, and it did not lost a single of it’s five petals. Which can also be seen on the retained weight (99,4%).

9,3×62 is more close range caliber than the previous tested Exergy calibers, so it is possible, that cartridges are adjusted for the shorter shooting distances. Of course we did not achieve the velocity that manufacturer promises, because of our 120mm shorter barrel. That also can affect to the working of the bullet.

At the impact of the 637m/s (2090fps) the bullet worked great again, and kept all the petals intact as can be seen on the photo above. The retained weight was also again excellent. With this velocity, the bullet width was almost exact same than it was on the harder hit. Only clear difference can be seen on the lenght of the bullet. Also with this Exergy cartridge, we can expect bullet to open reliably even on slightly longer distances.

RELOADING

This S&B Exergy .366″ 250gr bullet is only available in factory cartridges.

WOUND CHANNELS

Test targets were wetted newspapers. The bullet with impact speed of 714m/s (2343fps) penetrated 64cm (25,2″) of wet newspapers, and the bullet with impact speed of 637m/s (2090fps) penetrated 57cm (22,4″).

The wound channels can be seen below. Both are very classical example’s of the wound channels.

SUMMA SUMMARUM

Factory cartridge with a good copper bullet! You can expect good working at the over 100m distances also. Low ballistic coefficient (G1: 0,348) affects the velocity quite fast at the greater distances. Not the bullet for the real long range hunting, but at the normal hunting distances you can expect very good results on big-game hunting!

Sincerely yours – The Hard-Hitting Shooting Lab

Sellier & Bellot Exergy – 308win Factory Cartridge – Bullet test

We did a little Sellier & Bellot easter shootout at the last weekend! Thank you for the Aseliike Remes to make it possible! This is the second part of the article series that will concentrate on the S&B Exergy factory cartridges.  We already published the 6,5×55 test and this will concentrate on the 308win caliber. The 9,3×62 will follow on the next article! The S&B Exergy Blue bullet test articles will follow right after these Exergy articles!

Exergy is the original copper made hunting bullet of the Sellier & Bellot. At their homepage , they are writing that the jacket material of the Exergy, is not available. But on the Exergy 30-06 cartridge page, they are mentioning that it is made of 100% Solid Copper. So we cannot be sure about the exact material, but we know that it is a lead free bullet with little round aluminium tip on the top of the bullet.

Sellier Bellot exergy

But, to the results!

Sellier & Bellot Exergy 180gr –308 Winchester Factory Cartridge

TESTING

Test gun was a T3x rifle with the 600mm barrel. We measured the velocity ca. 5m from the muzzle and got a 804m/s impact velocity, which is little more than the manufacturer promises to the factory load ( 795m/s v0 @ 600mm barrel).

The slower impact velocity was achieved by reloading. If the velocity at the muzzle is 795m/s what manufacturer claims, the speed of 630m/s simulates the impact at the distance of 166 meters (ca. 181 yards).

THE BULLET

The working style of the S&B Exergy bullet is to open in five petals and retain its high weight after the impact without losing the petals.

The harder hit, with the velocity of 804m/s (2638fps) was too harsh for this 180gr Exergy bullet and it lost four of it’s five petals. Which can also be seen on the retained weight (77,9%). Result was quite same, as it was with the 6,5×55 130gr version of the Exergy. Like we wroted in that previous 6.5×55 article, this kind of close distance impacts are not common in normal hunting, so we don’t see this breakdown to be very significant thing. It tells us that the velocity of the factory cartridge has probably been adjusted to the working velocity area of the bullet. The more velocity you dare to add, the better and more reliably the bullet works at the longer distances. So the the breakdown at the close distances might be a well considered decision to achieve longer working distance to the factory cartridge.

At the impact of the 630m/s (2067fps) the bullet worked great and kept all the petals intact as can be seen on the photo above. The retained weight was also very good (98,4%). This slower velocity simulates the impact at the distance of 166 meters (ca. 181 yards) and the bullet opened almost to the bottom of the expansion cavity and achieved very good 16mm width! You can expect reliable working on the normal shooting distances!

RELOADING

This S&B Exergy .308″ 180gr bullet is only available in factory cartridges.

WOUND CHANNELS

Test targets were wetted newspapers. The bullet with impact speed of 804m/s (2638fps) penetrated 72cm (28,3″) of wet newspapers, and the bullet with impact speed of 630m/s (2067fps) penetrated 49cm (19,3″).

The wound channels can be seen below. From the upper diagram of the wound channel image, it is easy to see the effect of loosing the petals. Bullet has been broke immediately after the impact and made huge wound channel right from the outer surface. The remaining part of the bullet had smaller diameter and it penetrated a huge amount of wetted newspapers, because of the smaller resistance.

On the lower wound channel diagram, the bullet worked as planned. The wound channel is normal type, as is the depth of penetration also.

SUMMA SUMMARUM

Factory cartridge with a good copper bullet! Quite much same kind as the 6,5×55 130gr version on the previous article! You can expect good working at the wide velocity range. Low ballistic coefficient (G1: 0,287) affects the velocity quite fast at the greater distances. Not the bullet for the real long range hunting, but at the normal hunting distances you can expect very good results! Don’t forget the suprise factor possibility at the really close shooting distances.

Sincerely yours – The Hard-Hitting Shooting Lab

Sellier & Bellot Exergy – 6.5×55 Factory Cartridge – Bullet test

We did a little Sellier & Bellot easter shootout at the last weekend! Thank you for the Aseliike Remes to make it possible! This is the first part of the article series that will concentrate on the S&B Exergy factory cartridges. This part will consist the 6.5×55 caliber and the 308win, and 9,3×62 will follow in different articles! The S&B Exergy Blue bullet test articles will follow right after these Exergy articles!

Exergy is the original copper made hunting bullet of the Sellier & Bellot. At their homepage , they are writing that the jacket material of the Exergy, is not available. But on the Exergy 30-06 cartridge page, they are mentioning that it is made of 100% Solid Copper. So we cannot be sure about the exact material, but we know that it is a lead free bullet with little round aluminium tip on the top of the bullet.

But, to the results!

Sellier & Bellot Exergy 130gr – 6,5×55 Swedish Factory Cartridge

TESTING

Test gun was a Blaser combination gun with the 600mm barrel. We measured the velocity ca. 5m from the muzzle and got a 792m/s impact velocity, which is quite spot on to the promises of the manufacturer, which is 805m/s v0 velocity from the 600mm barrel.

The slower impact velocity was achieved by reloading. If the velocity at the muzzle is 805m/s, what the manufacturer claims. The speed of 691m/s simulates the impact at the distance of 91 meters (ca. 100 yards).

THE BULLET

The working style of the S&B Exergy bullet is to open in five petals and retain its high weight after the impact without losing the petals.

The harder hit, with the velocity of 792m/s (2592fps) was too harsh for this 130gr Exergy bullet and it lost three of it’s five petals. Which can also be seen on the retained weight (81,8%) This kind of close distance impacts are not common in normal hunting, so we don’t see this breakdown to be very significant thing. It tells us that the velocity of the factory cartridge has probably been adjusted to the working velocity area of the bullet. The more velocity you dare to add, the better and more reliably the bullet works at the longer distances. So the the breakdown at the close distances might be a well considered decision to achieve longer working distance to the factory cartridge.

At the impact of the 691m/s (2267fps) the bullet worked great and kept all the petals intact as can be seen on the photo above. The retained weight was also excellent. With this velocity, the bullet opened all-the-way to the bottom of the expansion cavity. So we can expect reliable opening of the bullet also on the greater distances than 91m/100yards.

RELOADING

This S&B Exergy .264″ 130gr bullet is only available in factory cartridges.

WOUND CHANNELS

Test targets were wetted newspapers. The bullet with impact speed of 792m/s (2592fps) penetrated 49cm (19,3″) of wet newspapers, and the bullet with impact speed of 646m/s penetrated 51cm (20,1″).

The wound channels can be seen below. With some bullets, it is easy to see the effect of loosing the petals, from the shape of the wound channel. But between these two, the difference is quite small.

SUMMA SUMMARUM

Factory cartridge with a good copper bullet! You can expect good working at the over 100m distances also. Low ballistic coefficient (G1: 0,240) affects the velocity quite fast at the greater distances. Not the bullet for the real long range hunting, but at the normal hunting distances you can expect very good results! Don’t forget the suprise factor possibility at the really close shooting distances.

Sincerely yours – The Hard-Hitting Shooting Lab